Can I Set Up A Tub Myself?
Can I Set Up A Tub Myself?
Blog Article
Have you been searching for info around Tools You Need to Install a New Bathtub ?
Installing a bathtub isn't exactly rocket science, but it does need strong plumbing, carpentry, and also often, tiling abilities. Replacing an old tub with a new one is also a reasonably tough project. If the old bathtub is conveniently obtainable, the job can move quickly; if you need to open a wall to remove the old bathtub as well as position the new bathtub, the job is a lot harder. In either situation, the project is within a home handyman's abilities, although you will certainly need a helper to vacate the old bathtub as well as set in the brand-new one. Make certain you have qualified on your own for the work as well as are comfortable attempting it. Rather than working with a service provider to take over a halfway-completed project, it is far better to think about employing one prior to you start. Chances are you might require a specialist plumber to make tube connections.
This article will certainly assist you install a brand-new tub in your bathroom if you have actually already purchased a new bathtub as well as do not require to change the setup of your previous supply of water pipes.
Your devices and product checklist need to make up the following:
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your installation, after that the first thing you ought to do is separate the supply of water. After doing so, activate the taps to drain pipes any type of water continuing to be in the system. The process of getting rid of the existing taps can be fairly problematic because of the restricted gain access to that is often the situation.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipes to the faucets. Have a towel ready for the remaining water that will certainly originate from the pipelines. Once the supply pipes have actually been gotten rid of, use the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the single faucets from transforming throughout this process. Once the taps have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned of any old sealing substance.
Prior to going on to fit the brand-new taps, compare the pipe connections on the old taps to the brand-new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the new taps to fit.
Fitting New Taps
If the tails of the new taps are plastic, then you will require a plastic port to stop damage to the thread. One end of the port fits on the plastic tail of the faucet and the other end offers a link to the current supply pipelines.
If you need to fit a monobloc, then you will need minimizing couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next, position the faucet in the placing opening in the bath/basin making certain that the washing machines remain in place between the tap and the sink. Secure the tap in place with the producer supplied backnut. When the faucet is firmly in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with typical tap connectors. The previous kind must be linked to the tap ends first, tightening up just by hand. The supply pipes can later be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Installing the Bath tub
Making use of both wooden boards under its feet, place the bath tub in the called for setting. The wooden boards are helpful in equally spreading out the weight of the tub over the area of the boards as opposed to concentrating all the weight onto four small factors.
The following goal is to ensure that the bath tub is leveled all round. This can be attained by checking the spirit level and also readjusting the feet on the tub up until the spirit level reads degree.
To mount taps, fit the bottom of the furthest versatile tap adapter to the proper supply pipeline by making a compression join; then do the very same for the various other tap.
Switch on the water supply and check all joints and also brand-new pipework for leaks and tighten them if essential. Fill up the bathtub as well as additionally inspect the overflow outlet and also the typical outlet for leakages.
Lastly, repair the bathroom paneling as explained in the producer's user's manual. Tiling as well as sealing around the bath tub must wait until the bath tub has actually been used at the very least once as this will certainly settle it right into its final placement.
Preparing for the Installment
Firstly, the sustaining frame provided with the bathroom ought to be fitted (if called for) according to the producer's guidelines. Next, fit the faucets or mixer to the bath tub. When fitting the faucet block, it is important to make certain that if the faucet comes with a plastic washing machine, it is fitted between the bath and also the taps. On a plastic bath, it is additionally sensible to fit a supporting plate under the faucets unit to avoid pressure on the bathtub.
Fit the versatile faucet connectors to the bottom of the two faucets making use of 2 nuts and olives (often supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet through the hole in the bath. Make use of the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Make certain you utilize every one of the provided washing machines.
Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom must currently be ready to be fitted in its final position.
Tiling Around the Bath tub
In the area where the bath meets the tile, it is required to seal the accompanies a silicone rubber caulking. This is very important as the installation can relocate sufficient to fracture an inflexible seal, creating the water to penetrate the wall between the bath and the tiling, leading to complications with dampness and feasible leakages to the ceiling listed below.
You can pick from a selection of coloured sealers to assimilate your components as well as installations. They are offered in tubes as well as cartridges, as well as are capable of sealing gaps up to a width of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of drenched newspaper or soft rope. Keep in mind to always fill the bathtub with water prior to securing, to enable the motion experienced when the tub is in use. The sealer can split relatively early if you do not consider this movement before securing.
Conversely, ceramic coving or quadrant ceramic tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also conveniently readily available on the market. It is recommended to fit the tiles making use of waterproof or water resistant adhesive and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I recently found that blog entry on Installing A Bathtub when looking around the web. So long as you enjoyed reading our post plz don't forget to share it. Bless you for your time. Please come by our site back soon.
Get Started
Report this page